**[转载]湍流强度 Turbulent Intensity 与雷诺数 Reynolds Number 的反比关系**

2020-3-30 11:51

阅读：7080

这个问题困扰了我很久

虽然每次都知道怎么设置湍流强度

参考link1

但是总有个疑惑:

为什么雷诺数 Re 越大，湍流强度* I *越小。

按照湍流强度的定义

5%* <I *< 20% 高湍流强度

1%* <I *< 5% 中湍流强度

* I *<1% 低湍流强度

层流状态下的 Re小，按照公式，

对应的湍流强度很大！

而高雷诺数时，湍流强度却很小。

2013年有个外国人提过这个问题

也有人解答了link2

我还是没太明白

贴一下回答吧，以备后面查阅

The issue here is that the Reynolds number is not a measure of "how turbulent" the flow is or will become. It is a ratio representing the relative importance of inertial forces to viscous forces in the flow. What they teach you in your first fluids class is often that above a certain Reynolds number, a pipe becomes turbulent, but this is only part of the picture. A boundary layer transitions because there are always some level of fluctuations in the free stream. These fluctuations, if they are of the right nature, can be entrained in the boundary layer by interacting with a surface; this is especially important early in the development of the boundary layer. Now, the boundary layer is actually a lot like a mass-spring-damper system, only a lot more complicated. In essence, it is a nonlinear oscillator which is subject to instability and resonance and all sorts of other good stuff that undergraduates often aren't taught about it. This means that when you have these small fluctuations that get entrained in the boundary layer, they are subject to the stability properties of boundary layer. A boundary layer is always unstable to some degree, so these fluctuations will tend to grow. If they grow enough, they become nonlinear, at which point the math becomes harder, but the overall concept of growth and decay stays the same. If they grow still further, they transition from a fluctuating laminar flow to the turbulent flow that everyone likes to talk about. The rate at which these fluctuations grow in the boundary layer tends to scale with Reynolds number. Now, back to the turbulence intensity that you are talking about. Typically, the turbulence intensity that you are describing is a measure of these free-stream fluctuations that started off the whole process mentioned above. In flight, they are typically close to zero. In a wind tunnel, they are generally around 1% or so unless you have a special, low-disturbance (or quiet) wind tunnel. It is an inlet conditions that you set based on the realities of the physical situation you are modeling, not some intrinsic property of the flow. For an open system (most external flows), this is entirely determined by the ambient conditions of what you are testing. A pipe is a special case since it is a closed system, i.e. it has no infinite boundaries. Often, when simulating a pipe, you assume it is already fully developed and therefore likely turbulent rather than trying to calculate all of that from the inlet of the pipe to where you are now, so you just prescribe a fully-developed turbulent flow at the inlet of your grid. To get the turbulent intensity there, you can scale it with Reynolds number. In reality, turbulent intensity tends to remain rather constant with Reynolds number, especially at reasonably high values of Re. Toward the lower end it is transitional, and a transitional boundary layer generally has larger fluctuations than a fully turbulent boundary layer. Source https://www.physicsforums.com/threads/reynolds-number-regarding-turbulent-intensity.676226/ |

转载本文请联系原作者获取授权，同时请注明本文来自姚程科学网博客。

链接地址：https://wap.sciencenet.cn/blog-531760-1225967.html?mobile=1

收藏

当前推荐数：1

推荐人：

推荐到博客首页
网友评论2 条评论