DOI: 10.1007/s12200-015-0546-3

Jiang TANG

 Full text PDF

Cite this article: Jiang TANG. A special section on Solar Cells, Light Emitting Diodes and Photodetectors[J]. Frontiers of Optoelectronics, 2015. 8(3): 239-240

DOI: 10.1007/s12200-015-0524-9

Xihua WANG

Abstract: The development of photovoltaic devices, solar cells, plays a key role in renewable energy sources. Semiconductor colloidal quantum dots (CQDs), including lead chacolgenide CQDs that have tunable electronic bandgaps from infrared to visible, serve as good candidates to harvest the broad spectrum of sunlight. CQDs can be processed from solution, allowing them to be deposited in a roll-to-roll printing process compatible with low-cost fabrication of large area solar panels. Enhanced multi-exciton generation process in CQD, compared with bulk semiconductors, enables the potential of exceeding Shockley-Queisser limit in CQD photovoltaics. For these advantages, CQDs photovoltaics attract great attention in academics, and extensive research works accelerate the development of CQD based solar cells. The record efficiency of CQD solar cells increased from 5.1% in 2011 to 9.9% in 2015. The improvement relies on optimized material processing, device architecture and various efforts to improve carrier collection efficiency. In this review, we have summarized the progress of CQD photovoltaics in year 2012 and after. Here we focused on the theoretical and experimental works that improve the understanding of the device physics in CQD solar cells, which may guide the development of CQD photovoltaics within the research community.

 Full text PDF

Cite this article: Xihua WANG. Recent progress in colloidal quantum dot photovoltaics[J]. Frontiers of Optoelectronics, 2015. 8(3): 241-251

DOI: 10.1007/s12200-015-0539-2

Cheng ZHANG,Jie ZHONG,Jiang TANG

Abstract: Cu₂ZnSn(S,Se)₄ (CZTSSe) is considered as the promising absorbing layer materials for solar cells due to its earth-abundant constituents and excellent semiconductor properties. Through solution-processing, such as various printing methods, the fabrication of high performance CZTSSe solar cell could be applied to mass production with extremely low manufacturing cost and high yield speed. To better fulfill this goal, environmental-friendly inks/solutions are optimum for further reducing the capital investment on instrument, personnel and environmental safety. In this review, we summarized the recent development of CZTSSe thin films solar cells fabricated with benign solvents, such as water and ethanol. The disperse system can be classified to the true solution (consisting of molecules) and the colloidal suspension (consisting of nanoparticles).Three strategies for stabilization (i.e., physical method, chemical capping and self-stabilization) are proposed to prepare homogeneous and stable colloidal nanoinks. The one-pot self-stabilization method stands as an optimum route for preparing benign inks for its low impurity involvement and simple procedure. As-prepared CZTSSe inks would be deposited onto substrates to form thin films through spin-coating, spraying, electrodeposition or successive ionic layer adsorption and reaction (SILAR) method, followed by annealing in a chalcogen (S- or Se-containing) atmosphere to fabricate absorber. The efficiency of CZTSSe solar cell fabricated with benign solvents can also be enhanced by constituent adjustments, doping, surface treatments and blocking layers modifications, etc., and the deeper research will promise it a comparable performance to the non-benign CZTSSe systems.

 Full text PDF

Cite this article: Cheng ZHANG,Jie ZHONG,Jiang TANG. Cu₂ZnSn(S,Se)₄ thin film solar cells fabricated with benign solvents[J]. Frontiers of Optoelectronics, 2015. 8(3): 252-268

DOI: 10.1007/s12200-015-0531-x

Mingzhang DENG,Weina SHI,Chen ZHAO,Bingbing CHEN,Yan SHEN

Abstract: The work function (WF) of indium-tin-oxide (ITO) substrates plays an important role on the inverted organic photovoltaic device performance. And electrode engineering has been a useful method to facilitate carrier extraction or charge collection to enhance organic photovoltaic (OPV) performance. By using self-assembly technique, we have deposited poly(dimethyl diallylammonium chloride) (PDDA) layers onto ITO coated glass substrates. The results indicate that the surface WF of ITO is reduced by about 0.3 eV after PDDA modification, which is attributed to the modulation in electron affinity. In addition, the surface roughness of ITO substrate became smaller after PDDA modification. These modified ITO substrates can be applied to fabricate inverted OPVs, in which ITO works as the cathode to collect electrons. As a result, the photovoltaic performance of inverted OPV is substantially improved, mainly reflecting on the increase of short circuit current density.

 Full text PDF

Cite this article: Mingzhang DENG,Weina SHI,Chen ZHAO,Bingbing CHEN,Yan SHEN. ITO surface modification for inverted organic photovoltaics[J]. Frontiers of Optoelectronics, 2015. 8(3): 269-273

DOI: 10.1007/s12200-015-0522-y

Jiayun XIANG,Han NIE,Yibin JIANG,Jian ZHOU,Hoi Sing KWOK,Zujin ZHAO,Ben Zhong TANG

Abstract: By melting tetraphenylethene (TPE) and 1,2,4,5-tetraphenyl-1H-imidazole (TPI) units together through different linking positions, three new fluorophores are synthesized, and their optical, electronic and electroluminescence (EL) properties are fully studied. Owing to the presence of TPE unit(s), these fluorophores are weak emitters in solutions, but are induced to emit strongly in the aggregated state, presenting typical aggregation-induced emission characteristics. The experimental and computational results reveal that different connection patterns between TPE and TPI could impact the molecular conjugation greatly, leading to varied emission wavelength, fluorescence quantum yield and EL performance in organic light emitting diodes (OLEDs). The fluorophore built by attaching TPE unit to the 1-position of imidazole ring shows bluest fluorescence, and its EL device emits at deep blue region (445 nm; CIE= (0.16, 0.15)). And the device based on the fluorophore by linking TPE to the 2-position of imidazole ring shows EL at 467 nm (CIE= (0.17, 0.22)) with good efficiencies of 3.17 cd·A^-1, and 1.77%.

 Full text PDF

Cite this article: Jiayun XIANG,Han NIE,Yibin JIANG,Jian ZHOU,Hoi Sing KWOK,Zujin ZHAO,Ben Zhong TANG. Blue fluorophores comprised of tetraphenylethene and imidazole: aggregation-induced emission and electroluminescence[J]. Frontiers of Optoelectronics, 2015. 8(3): 274-281

DOI: 10.1007/s12200-015-0529-4

Taotao DING,Yu TIAN,Jiangnan DAI,Changqing CHEN

Abstract: In this paper, Bi₂S₃ nanorods were successfully synthesized via a facile one-pot hydrothermal method and characterized by X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy and X-ray photoelectron spectroscopy. Then the Bi₂S₃ nanorods were deposited on Au interdigital electrodes by dip-coating to fabricate photodetectors. The photoresponse properties using Bi₂S₃ nanorods as a representative system showed a significantly enhanced conductivity and the current-voltage (I-V) characteristic exhibited about ca. 2 orders of magnitude larger than the dark current. The response and decay time was estimated to be ~371.66 and 386 ms, respectively, indicating Bi₂S₃ may be an excellent candidate for high speed and high-sensitivity photoelectrical switches and light sensitive devices.

 Full text PDF

Cite this article: Taotao DING,Yu TIAN,Jiangnan DAI,Changqing CHEN. Building one-dimensional Bi₂S₃ nanorods as enhanced photoresponding materials for photodetectors[J]. Frontiers of Optoelectronics, 2015. 8(3): 282-288

REGULAR PAPERS

RESREARCH ARTICLE

DOI: 10.1007/s12200-015-0527-6

Sujata CHAKRABORTY,Nabin Baran MANIK

Abstract: In this work, we investigated the effect of single walled carbon nanotubes (SWCNT) on the electrical and photovoltaic properties of methyl red (MR) dye based photoelectrochemical cell (PEC). MR dye based PEC with LiClO₄ as ion salt were fabricated with and without mixing SWCNT. The cells were characterized through electrical and optical measurements. The performance of the devices changed drastically in presence of SWCNT. The transition voltage and trap energy of the cells were estimated from the steady-state dark current voltage (I-V) analysis. The transition voltage and trap energy decreased for MR dye cell in presence of SWCNT. Open circuit voltage (V_oc), short circuit current (J_sc), fill factor (FF) and power conversion efficiency (η) increased due to the addition of SWCNT. Further measurement of the transient photocurrent showed that the growth and decay of photocurrent was quite faster in presence of SWCNT. The photocurrent decay with time was fitted for both the cells and found to follow a power law relation which indicates dispersive transport mechanism with exponential trap states distributed in between lowest unoccupied molecular orbital (LUMO) and highest occupied molecular orbital (HOMO) levels. Possible interpretation is done on the lowering of trap energy with the photocurrent. These results suggest that SWCNT lowers the trap energy of the cells by providing efficient percolation pathways for the conduction of charges. It is expected that due to lowering of trap energy the residing time of the free carriers within the traps decreases. In other words, it may also be said that the charge recombination decreases. These factors affect the overall conduction of charges and improve the electrical and photovoltaic properties.

 Full text PDF

Cite this article: Sujata CHAKRABORTY,Nabin Baran MANIK. Improvement of electrical and photovoltaic properties of methyl red dye based photoelectrochemical cells in presence of single walled carbon nanotubes[J]. Frontiers of Optoelectronics, 2015. 8(3): 289-297

DOI: 10.1007/s12200-014-0372-z

Qingsong LEI,Jiang LI

Abstract: Al doped zinc oxide (AZO) films were prepared by mid-frequency magnetron sputtering for silicon (Si) thin film solar cells. Then, the influence of deposition parameters on the electrical and optical properties of the films was studied. Results showed that high conductive and high transparent AZO thin films were achieved with a minimum resistivity of 2.45 × 10^-4 Ω?cm and optical transmission greater than 85% in visible spectrum region as the films were deposited at a substrate temperature of 225°C and a low sputtering power of 160 W. The optimized films were applied as back reflectors in a-SiGe:H solar cells. A relative increase of 19% in the solar cell efficiency was achieved in comparison to the cell without the ZnO films doped with Al (ZnO:Al).

 Full text PDF

Cite this article: Qingsong LEI,Jiang LI. High conductive and transparent Al doped ZnO films for a-SiGe:H thin film solar cells[J]. Frontiers of Optoelectronics, 2015. 8(3): 298-305

DOI: 10.1007/s12200-014-0401-y

Haobo CHENG,Jingshi SU,Yong CHEN,Hon-Yuen TAM

Abstract: This paper focuses on the process of electrorheological (ER) finishing optical surfaces. Experiments on K9 mirrors were conducted. In one experiment, the operating distance was varied over 0.5–0.8 mm with the voltage at 2000 V. The maximum peak-to-valley (PV) reduction was obtained at the distance of 0.5 mm, where the PV value was reduced from 58.71 to 25.03 nm. In another experiment, the voltage was varied over 1500–3000 V with operating distance at 0.5 mm. The final surface roughness (Ra) achieved was as low as 2.5 nm. A higher voltage produced a higher relative reduction of the Ra. These experimental results validated the process.

 Full text PDF

Cite this article: Haobo CHENG,Jingshi SU,Yong CHEN,Hon-Yuen TAM. Profile and roughness of electrorheological finishing optical surfaces[J]. Frontiers of Optoelectronics, 2015. 8(3): 306-313

DOI: 10.1007/s12200-015-0447-5

Saeed OLYAEE,Hassan ARMAN

Abstract: The propagation loss of a fiber can be increased by coupling core mode and surface mode which will deteriorate the performance of photonic bandgap fiber (PBGF). In this paper, we presented an air-core PBGF for gas sensing applications. By designing Λ = 2.63 µm, d = 0.95 Λ, andR_core= 1.13 Λ, where Λ is the distance between the adjacent air holes, the fiber was single-mode, no surface mode was supported with fiber, and more than 90% of the optical power was confined in the core. Furthermore, with optimizing the fiber structural parameters, at wavelength of λ = 1.55 µm that is in acetylene gas absorption line, significant relative sensitivity of 92.5%, and acceptable confinement loss of 0.09 dB/m, were simultaneously achieved.

 Full text PDF

Cite this article: Saeed OLYAEE,Hassan ARMAN. Improved gas sensor with air-core photonic bandgap fiber[J]. Frontiers of Optoelectronics, 2015. 8(3): 314-318

DOI: 10.1007/s12200-015-0453-7

Yubin WU,Shixiong JIANG,Zhenkun XU,Song ZHU,Danhua CAO

Abstract: This paper proposes a detection method of chessboard corner to correct camera distortions –including radial distortion, decentering distortion and prism distortion. This proposed method could achieve high corner detection rate. Then we used iterative procedure to optimize distortion parameter to minimize distortion residual. In this method, first, non-distortion points are evaluated by four points near image center; secondly, Levenberg-Marquardt nonlinear optimization algorithm was adopted to calculate distortion parameters, and then to correct image by these parameters; thirdly, we calculated corner points on the corrected image, and repeated previous two steps until distortion parameters converge. Results showed the proposed method by iterative procedure can make the impact of slight distortion around image center negligible and the average of distortion residual of one line is almost 0.3 pixels.

 Full text PDF

Cite this article: Yubin WU,Shixiong JIANG,Zhenkun XU,Song ZHU,Danhua CAO. Lens distortion correction based on one chessboard pattern image[J]. Frontiers of Optoelectronics, 2015. 8(3): 319-328

DOI: 10.1007/s12200-015-0476-0

Abbas GHADIMI,Alireza AHADPOUR SHAL

Abstract: In this paper, ridge waveguide quarterly wavelength shifted distributed feedback (RW-QWS-DFB) laser was modeled and analyzed. In this behavioral model, some characteristics of the device, such as threshold current, line width, power of output wave, spectrum of output wave, and laser stability in high powers, were investigated in accordance with different physical and geographical parameters such as sizes and structures of the layers. Considering a new proposed algorithm, the analysis of the mentioned structures was performed using transfer matrix method (TMM), the solution of coupled waves and carrier rate equations. The results showed the advantages of some parameters in this structure.

 Full text PDF

Cite this article: Abbas GHADIMI,Alireza AHADPOUR SHAL. Analysis and modeling of ridge waveguide quarterly wavelength shifted distributed feedback laser with three rate equations[J]. Frontiers of Optoelectronics, 2015. 8(3): 329-340